Install Flash Player

ACCESSORIES

Leveling system – small

Leveling system – full version

Rubber matting:

  • It helps you to secure the FIS safety area.
  • We recommend using it on ski-jumping hills where ice in-run track is used (winter and summer track).
  • It is black in color and is 23 mm high. The dimensions may vary depending on application.
  • This rubber matting decreases the amount of slickness of the slope. The crampons can be used on this matting.

Cover system:

  • Can be delivered in different sizes (length and width), colors and prints.
  • The cover weighs approximately 1 kilo per 1 square meter. It should be used in conjunction with an electronic winch (positioned on the top of the ski-jumping hill, option: wireless control). The speed of the winch varies between 10 and 30 meters per minute.
  • The grooves are cone-shaped and can be up to 10 millimeters deep. The position of the grooves can be customized. The default specification of the grooves are tree grooves, which are equally distributed at the heater width.
  • The ironing device comes with a heat sensor and an electronic heat adjuster.
  • It is made out of stainless steel and can be bolted onto the carrier without the use of tools.

Ironing device::

  • This device is part of the accessories for track preparation, in addition to the snow mixture case, multifunctional carrier and ice tiller/mill.
  • It comes with two sets of heaters: flat and grooved.
  • It should be used with a cover role at the take-off point. This cover role is specially designed, as based upon ski-jumping hill specifics. However, the minimal requirements of ski-jumping construction should be fulfilled prior to installation of the cover system.

Snow mixture case:

  • This case is part of the accessories for track preparation, in addition to the ironing device, multifunctional carrier and ice tiller/mill.
  • It is used for specific amounts of mixing snow and water. The resulting snow mixture is than inserted into the in-run track.
  • It is made out of stainless steel and can be bolted onto the carrier without the use of tools.

Artificial grass matting

  • It helps you cover the base construction of the ski-jump.
  • We recommend using it on ski-jumping hills where only ceramic in-run track is used (only summer track).

Multifunctional carrier

  • This carrier is part of the accessories for track preparation, in addition to the snow mixture case, ironing device and ice tiller/mill.
  • It is made out of stainless steel. It is adjusted to carry the ironing device, snow mixture case, and ice tiller/mill, and it can also be used for pulling up the in-run track cover.
  • The design of the carrier comes in one style, however, it can be adjusted if the client wants a custom design.

Ice tiller/mill

  • This tiller/mill is part of the accessories for track preparation, in addition to the snow mixture case, multifunctional carrier and ironing device.
  • The ice tiller/mill is electrically driven, has no exhaust and is environmentally friendly.
  • It has a low noise lever and is highly effective in cutting ice.
  • When combined with the ironing device, you will have the ultimate snow channel preparation kit.

Cooling system:

  • Comes in two versions: internal or external. The internal version is for ski-jumping centers that contain a specially designed place to contain a cooling system. The external version is for ski-jumping centers that do not contain a specially designed place for a cooling system.
  • It has low power consumption and can be handled after only two hours of training.
  • It contains two cooling units which work as a back-up system. If one unit fails to work, the other takes over.
  • The external version comes in a protective case, but the investor should still provide a roof to protect the cooling system from outside elements. Installation of cooling device also requires a concrete base.
  • For a K90 hill we usually use 10kW of cooling power. 12kW with 28A power connection is needed.
  • All our cooling devices include a heater that melts snow, ice or frost which may form on the in-run track.
  • The cooling agent we use is non-toxic glycol.


SERVICES



Technical assistance:

  • This tiller/mill is part of the accessories for track preparation, in addition to the snow mixture case, multifunctional carrier and ironing device.
  • The ice tiller/mill is electrically driven, has no exhaust and is environmentally friendly.
  • It has a low noise lever and is highly effective in cutting ice.
  • When combined with the ironing device, you will have the ultimate snow channel preparation kit.

Ice tiller/mill

  • New in-run tracks come with a lot of new technical equipment. This equipment should be properly used to extend its expected life.
  • We can assist you when you have an important ski-jumping competition or other event during which you will not have your own technical team.
  • The technical assistance covers: use of winch, use of covering system, use of ironing device, use of multipurpose carrier, use of cooling aggregate, use of special tools (hobl, etc.), and so on.

In-run track preparation:

  • if the in-run track is being prepared for a ski-jumping competition or any other important event and you don’t have experienced crew.
  • Preparation can include anything from preparing the entire track from scratch to merely fine tuning an existing snow surface.
  • The in-run track preparation team should be reserved in advance.
  • This first preparation of the in-run track is included in the price of the TopSpeed® ice in-run track, as long as preparation can be made immediately after the assembly of the in-run track.

Education:

  • We can educate your team on how to prepare an in-run track in summer and winter conditions, how to handle technical issues and how to maintain the system.
  • First level education is included in the price of all TopSpeed® in-run tracks.

System maintenance:

  • The cooling system should be properly maintained in order to work effectively for a longer time period. We can offer full cooling system service. If you decide to enroll in our cooling system service, the guarantee for the cooling system is automatically extended.
  • Before the winter or summer season, it is wise to check all critical points of the system. Right maintenance can extend the life of the system. If you don’t know how to do it or you don’t have an appropriate team to do it, we can do it for you.

Track modernization consulting:

  • If you decide to modernize your current jumping hill with new in-run track, we can help you with our extensive experience in this field.
  • We offer consulting as to the use of materials, equipment selection, architectural aspects, and engineering.